CFM Performance Twin 67mm Throttle Body
The CFM Performance Twin 67mm Throttle Body is a direct replacement for both the 2007-2013 Mustang Shelby GT500 and 2011-2013 Mustang GTs with Ford Racing Supercharger Kit M-6066-MGT624D. Recently tested on a Dynojet, our Twin 67mm Throttle Body showed an increase of 37 horsepower and 26 lb.-ft. of torque on a stock 2013 Mustang Shelby GT500.
- Made in USA
- Direct replacement for 2007-2013 Mustang Shelby GT500
- Precision machined billet aluminum housing
- Custom twin 67mm bores provide maximum air flow
- OEM gears, throttle position sensor and drive motor
- Factory calibration method used for idle air flow
- Beautiful polished show finish
- Custom calibration required due to increased air flow
Ford Racing Cobra Jet Intake Manifold
â€˘ Fits 2011-2014 Mustang GT and 2012-2013 Boss 302
â€˘ Based on intake manifold used on naturally aspirated version of 2013 Mustang Cobra Jet Race Car
â€˘ Significant power increase above the M-9424-M50BR Ford Racing Boss 302 intake manifold with no loss of torque.
â€˘ Runners tuned for 7750 RPM peak power
â€˘ Made from light-weight composite material
â€˘ Total intake volume 635 cubic inches
â€˘ Designed and tested to 20+ PSI
â€˘ O-ring intake gaskets included
â€˘ Requires Cobra Jet 5.0L Cold Air Kit M-9603-M50CJ to mate to oval throttle body
â€˘ Mustang GT requires installation kit M-9444-M50B or equivalent (inlet hose in kit not used)
â€˘ Compatible with production 5.0L Ti-VCT fuel rail
â€˘ Not compatible with strut tower brace
â€˘ Nitrous oxide not recommended for use with this manifold
â€˘ Calibration is necessary to prevent engine damage! Calibration not included!
Ford Racing Cobra Jet 5.0L 4V Cold Air Kit (Option)
Fits 2011-2014 Mustang GT and 2012-2013 Boss 302 with Cobra Jet 5.0L Intake Manifold M-9424-M50CJ
Intake manifold requires CFM Twin 67mm throttle body with part number 4-1060-P
High flow filter, high flow molded plastic air filter bucket and unique clean-air inlet tube with Ford Racing logo.
102mm air inlet diameter
Calibration is necessary to prevent engine damage! Calibration not included!
JLT Cobra Jet Cold Air Kit (Option)
NOW SHIPPING- the JLT Cobra Jet CAI.
The perfect balance between size, 110mm which can easily support well over 600 RWHP and fit.
110mm makes it easy to tune and the smooth large bend makes it flow massive amounts of air to the large twin bore throttle body.
With a huge 4.5â€ť opening on the tube we needed a huge filter. We love the tapered flange design and Powerstack filtered ends of S&B's filters and ended up with a monster 4.5x9â€ť filter. Finish it off with a silicone coupler and stainless clamps and you got the BEST Intake on the market!!! NO METAL TUBING HERE!!
Automatic cars need an additional fitting, which JLT will provide. The fittings are Milled from solid billet aluminum and all you need to do is drill a Â˝â€ť hole (JLT shows you where) in the tube, install the supplied grommet, fitting and youâ€™re done. Note, all kits sold to resellers will include the automatic fitting.
MOLDED IN MAF
Itâ€™s a full 110mm ID at the MAF area
The heat shield ABS plastic to block engine heat at idle and low speed.
It incorporates the fresh air inlet from the grill.
It uses a large area to make sure the filter has tons of cool air.
Standard finish is an OEM looking black textured plastic.
â€˘JLT Plastic intake tube
â€˘4.5x9 S&B powerstack air filter
â€˘ABS Heat Shield
â€˘OEM style PCV connection hose
â€˘2013-14 Hood Insert Plug
â€˘HD Clamps & all needed hardware
A JLT specific tune is required with this kit.
Not C.A.R.B. approved
2013-14 owners, ALL JLT KITS NOW INCLUDE OUR WATER BLOCKER PLUG INSERT FOR NO WORRIES ABOUT WATER GETTING TO THE FILTER.